Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateTrusted Gate Repair for Richmond Homeowners
A gate that won’t open, drags on the ground, or stops halfway leaves you parked in the street and your property open to anyone who walks by. Our gate-only technicians diagnose the problem on the first visit, whether it’s a bent hinge on a wrought iron walk gate or a DoorKing control board that’s stopped answering the keypad. Our technicians have up to 12 years of experience working on gates, not garage doors or fences, and they arrive already familiar with how your brand fails and where. Same-day service is often available in Richmond when you call early, and the price is quoted and agreed before any work starts. Call (866) 942-6565. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Driveway Gate Repair
Driveway Gate Repair covers the wide, heavy swing and slide gates that guard a vehicle entrance, and it’s the most common call we get in Richmond. When a driveway gate sags, scrapes the driveway, or stops responding to a remote, the cause is usually a worn hinge, a tired operator, or a post that has shifted in our clay-heavy soil. We work on manual and automated driveway gates, diagnose the mechanical and electrical side in one visit, and reset the gate so it swings or slides cleanly again. Typical driveway gate repair in Richmond runs $175-$450 depending on whether the fix is mechanical or electrical, with operator or control board work at the higher end. The written estimate sets the final price, and it’s free.
Post and Hinge Alignment
A driveway gate lives or dies by its posts. When a post leans or a hinge wears, the gate drops, drags, and strains the operator until something gives. We check post stability and hinge wear first on any driveway gate call.
Operator and Arm Repairs
Swing-arm and slide operators take a beating on a heavy driveway gate. We diagnose motor strain, limit switches that are out of adjustment, and arms that have come loose from the gate frame. Getting the operator matched to the gate’s weight is half the repair.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Gate Welding
Gate Welding is the structural repair that brings a cracked frame, a snapped hinge bracket, or a separated picket back to solid metal, and it’s what you need when a gate has failed at a joint rather than at a moving part. Impact from a vehicle, decades of rust at a weld, and metal fatigue on a heavy swing gate all show up as a break you can see or a wobble you can feel. Our technicians weld steel and wrought iron frames on site where the joint allows, or pull the gate for bench welding when the break is structural. Typical gate welding in Richmond runs $150-$400 depending on the number of joints and whether the gate has to come off its hinges. The price is agreed from the written estimate before we strike an arc.
Frame and Joint Repairs
Cracks at a corner or a rail-to-stile joint are the first thing we look for after an impact. A weld that fails there can let a whole panel twist. We grind back the old weld, re-fit the joint, and weld it properly rather than laying a patch over the crack.
Hinge and Bracket Welding
Hinge brackets carry the full weight of the gate every time it swings, so they’re a common failure point on older iron gates. We re-weld brackets to the frame and check the hinge pin isn’t worn past its tolerance. A bracket that’s welded back in the wrong spot will just drag again next month.
Commercial Gate Repair
Commercial Gate Repair handles the access gates on parking lots, apartment communities, and business entrances where a stuck gate holds up traffic and creates a real liability. When an entry gate won’t open for a tenant’s card, a loop detector stops seeing cars, or a slide gate jams at peak hours, the fix has to happen fast and it has to stick. We diagnose DoorKing and LiftMaster access systems, loop and safety-edge faults, and motor failures that general contractors won’t touch. Typical commercial gate repair in Richmond runs $250-$650 depending on whether the work is mechanical, electrical, or access-control related. You get a written estimate before any work begins, and it’s free.
Access Control and Loop Detectors
Most commercial gate failures aren’t the gate at all, they’re the system telling it what to do. We test loop detectors, keypads, card readers, and safety edges to find the fault before replacing anything. Intercom and entry-system wiring is part of the diagnostic.
Traffic Flow and Safety Edges
A commercial gate that closes on a car is a serious problem, and a safety edge that’s failed is the usual cause. We check the reversing edge, the photo-eye, and the closing-force settings. Getting the gate to stop and reverse correctly is as important as getting it to open.
Iron Gate Repair
Iron Gate Repair covers the ornamental iron walk gates and driveway gates that have bent, rusted, or come loose from their posts. Ornamental iron looks permanent, but a gate that’s been hit, has rusted through at a hinge, or has a post pulling out of the ground will fail just like any other. We straighten bent frames, repair hinges and latches, treat rust at the joints, and reset gates that no longer sit true in the opening. Typical iron gate repair in Richmond runs $175-$450 depending on the extent of the damage and whether welding is needed. We look at the gate and give you a written price before any work starts.
Rust and Corrosion Repair
Richmond’s humid summers and freeze-thaw winters work on iron joints year after year. Rust starts at a weld or a scratch and creeps under the paint until the section is weak. We clean back to sound metal before we repair, or the fix won’t hold.
Bent Frame Straightening
An iron gate that’s been backed into rarely looks bent until you try to close it. Twisted frames bind at the latch and strain the hinges. We straighten the frame back to the opening rather than forcing the latch to compensate.
Sliding Gate Repair
Sliding Gate Repair gets a gate that has jumped its track, drags on the ground, or won’t roll smoothly back onto its rollers. A slide gate that comes off the track is one of the more dangerous gate failures there is, because a heavy panel can fall or swing free, so it’s not something to force by hand or push back into place with a car. We check the track for misalignment, replace worn rollers and guide posts, and diagnose the operator if the gate moves but stalls. Typical sliding gate repair in Richmond runs $200-$500 depending on whether the problem is the track, the rollers, or the operator. The price comes from a written estimate and it’s free.
Track and Roller Repairs
A slide gate runs on its track and rollers, and either one failing will drag the gate. We check for a track that’s lifted or filled with grit, and for rollers that have flat-spotted or seized. Replacing one without checking the other usually means a return visit.
Guide Posts and Stops
Guide posts keep a slide gate from drifting off line as it closes. When a guide post shifts or a stop is missing, the gate wanders and can come off the track. We reset the posts and check the travel limits at both ends.
Wrought Iron Gate Repair
Wrought Iron Gate Repair restores the ornate, decorative gates that are common on older Richmond properties and historic neighborhoods, where the gate is as much a feature as it is a barrier. These gates carry a lot of weight in their scrollwork and finials, and when a joint fails or a hinge wears out, the whole gate can sag and bind. We repair decorative ironwork, re-weld broken scrolls and joints, replace worn hinges and latches, and straighten frames without losing the original look. Typical wrought iron gate repair in Richmond runs $175-$475 depending on the detail of the ironwork and whether welding is involved. We quote from a written estimate before any work starts.
Decorative Ironwork Repairs
Scrollwork and finials are often the first things to break because they take the impact. We match the repair to the existing pattern so a mended gate doesn’t look mended. Where a piece is too far gone to repair, we can discuss what replacing that section involves.
Hinge and Latch Restoration
Old wrought iron gates often have hinges and latches that are as old as the gate. When they wear, the gate sags and stops latching cleanly. We restore or replace the hardware to bring the gate back into alignment.
Metal Gate Repair
Metal Gate Repair handles the steel, aluminum, and mixed-metal gates that don’t fit neatly into the iron or wood categories, from a simple tubular steel walk gate to an aluminum driveway gate with an operator. Metal gates fail at the welds, the hinges, and the latch, and an aluminum gate can crack at a joint that steel would just bend at. We repair frames, hinges, latches, and operators across metal gate types, and we know which repairs work on aluminum and which need a different approach from steel. Typical metal gate repair in Richmond runs $150-$425 depending on the metal and the damage. The written estimate is free and sets the final price.
Aluminum and Steel Repairs
Aluminum and steel fail differently, and the repair has to match the metal. Aluminum can crack where steel would bend, and welding aluminum takes different equipment. We identify the metal first so the repair is right the first time.
Latch and Hardware Replacement
Latches and hardware take more wear than any other part of a metal gate. A latch that’s worn or misaligned lets the gate swing or refuses to catch at all. We replace the hardware and adjust it so the gate latches cleanly every time.
Wood Gate Repair
Wood Gate Repair covers the wooden walk gates, garden gates, and driveway gates that age faster than metal in Richmond’s wet winters and humid summers. Wood swells, warps, rots at the base, and pulls its hinges out of soft grain, and a gate that was fine last spring can be dragging by fall. We repair rotted sections, re-hang sagging gates, replace worn hinges and latches, and reset posts that have shifted. Typical wood gate repair in Richmond runs $150-$400 depending on how much rot has to be cut out and whether the gate needs re-hanging. The price is set from a written estimate you get before any work begins, and the estimate is free.
Rot and Warp Repairs
Rot starts at the bottom rail and the hinge edge, where water sits longest. A gate that’s warped or soft at the base won’t stay true no matter how often you adjust the hinges. We cut out the rot and replace it with sound wood before we re-hang anything.
Sagging and Re-Hanging
A wooden gate sags when the hinge screws pull out or the post has leaned. Tightening the screws seldom holds for long. We reset the post, repair the hinge edge, and re-hang the gate so it swings and latches properly.
See the difference
Before
After
Before
After
Before
AfterBrands We Service
We work on nine major gate and operator brands, and that breadth means we don’t have to guess at your system. We service LiftMaster operators regularly and know the control board and limit-switch quirks that show up on their slide and swing units. DoorKing access systems are built for commercial traffic, and we know where the loop detectors, keypads, and entry wiring tend to fail. Elite equipment shows up on plenty of residential driveway gates, and we’re familiar with its operator behavior and common fault points.
Mighty Mule is a common DIY-installed brand, and we often get called to fix installations that were never dialed in properly, from the arm angle to the limit settings. Whether you have a LiftMaster, DoorKing, Elite, or Mighty Mule gate, or any other make, we can help. Our technicians diagnose motor failures, control boards, and safety devices across all nine brands we service, and they arrive already familiar with your system rather than looking it up on the spot. If you’re ready for a specialist who works on gates every day, Richmond Gate Repair is one call away.
Signs You Need a Pro Right Now
- The gate won’t close on its own. An operator that stalls or stops short is usually a limit switch, a control board, or a failing motor. Left alone, a gate that won’t close leaves the driveway open, so this is worth a same-day call.
- The gate drags or scrapes. A gate scraping the ground means a hinge has worn, a post has shifted, or a roller has failed. Dragging strains the operator until it fails too, so fixing it early saves the motor.
- The gate is visibly bent or the post is leaning. Impact damage and leaning posts both throw the gate out of alignment. A gate that sits crooked binds at the latch and hits the operator hard every cycle.
- A slide gate has come off its track. This is a real safety hazard, since a heavy panel can fall or swing free. Don’t force it back by hand or with a vehicle; keep people clear and get a technician out.
- The keypad, remote, or intercom has stopped working. Access-control failures are often a loop detector, wiring, or control board issue, not the gate itself. These are exactly the faults a general contractor or handyman can’t diagnose.
Our Process, Step by Step
- 1
Call and describe the problem. Tell us the gate type, the brand if you know it, and what it’s doing. That helps us arrive with the right diagnostic gear and the right operator parts, and it’s how we can often schedule same-day service in Richmond.
- 2
On-site diagnosis. We test the full system, not just the part you noticed. That means checking the gate’s travel and alignment, then testing the operator, limit switches, control board, and any loop detectors or safety edges on the system.
- 3
Written estimate before any work. We explain what’s wrong and what it takes to fix it, and we put the price in writing. You agree to it before we start. No surprise invoice at the end.
- 4
The repair, done right the first time. Because we work on gates every day and know the nine brands we service, we repair to the manufacturer’s design rather than working around it. Most repairs are completed on the first visit.
- 5
Full test and walkthrough. We cycle the gate through open and close, test the safety devices, and confirm the latch and stops. Then we walk you through what we did and what to watch for going forward.
How Much Does Gate Repair Cost in Richmond?
A typical gate repair in Richmond runs $150-$650 depending on the type of gate and whether the problem is mechanical or electrical. Simple mechanical fixes like a hinge, latch, or roller usually land at the low end, while operator, control board, and access-control work on a commercial or automated gate run higher. Welding and structural repairs fall in the middle.
A few things move the price. The gate type matters, since a decorative wrought iron gate with fine scrollwork takes more careful repair than a plain steel frame. The brand and operator matter too, because a LiftMaster or DoorKing control board costs more than a mechanical part. Whether the gate has to come off its hinges or the posts have to be reset also affects the labor. Knowing the gate type and brand before you call helps us give a straighter estimate.
To avoid overpaying, get the price in writing before any work starts and ask what’s included. A free estimate from us covers the diagnosis and a written price for the repair. We don’t quote a number over the phone and then change it on site. If the repair turns out to be bigger than expected, we tell you before we go ahead. Call (866) 942-6565 for an exact quote; estimates are free.
Our Service Area Near Richmond
We cover Richmond and the surrounding communities, including Manchester, Bon Air, Montrose, Lakeside, East Highland Park, Dumbarton, Bensley, Meadowbrook, Chamberlane, Rockwood, and Tuckahoe. Response times vary by location and the day’s schedule, and same-day service is often possible when you call early. If you’re in one of these areas, we can usually get a technician out the same day for a repair. For routine maintenance on a gate, gate repair in Manchester is handled by the same specialist team. Neighbors in Bon Air can reach us at gate repair in Bon Air as well.
Serving Richmond, VA – Our Local Coverage Area
We serve Richmond and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions About Gate Repair in Richmond
Gate repair is the diagnosis and fixing of a gate that won’t open, won’t close, drags, sags, or has stopped responding to its operator or controls. It covers the mechanical parts like hinges, latches, rollers, and posts, as well as the electrical side like the operator, control board, and access control. A dedicated gate specialist handles both, so you don’t need two different trades. Call (866) 942-6565 for an exact quote; estimates are free.
Most gate repairs are completed in a single visit, and many take under two hours. A hinge, latch, or roller replacement is quick, while operator or control board work can take longer depending on the brand and access. If the repair needs parts ordered, we tell you the timeline before we start. We’ll give you a clear answer on timing when you call.
Most gate repairs in Richmond run $150-$650 depending on the gate type and whether the work is mechanical or electrical. Welding, ironwork, and access-control repairs sit at the higher end. The final price comes from a written estimate you agree to before any work starts. Call (866) 942-6565 for an exact quote; estimates are free.
Yes, we service LiftMaster and DoorKing systems, along with FAAC, BFT, Linear, Viking, Ghost Controls, Elite, and Mighty Mule. We work on these brands every day and know where each one tends to wear out and fail. That means faster diagnosis and fewer return visits. Call (866) 942-6565 for an exact quote; estimates are free.
Same-day service is often available in Richmond when you call early in the day. We answer 24/7, and fast dispatch runs from 7am to 7pm, Sunday through Friday. We’re closed on Saturday, and a call outside dispatch hours is booked into the next opening. Call (866) 942-6565 and we’ll find you the soonest slot.
Warranty terms depend on the repair and the parts used, so we confirm them in writing with your estimate. We stand behind the work and want the repair to hold, which is why we test every gate through a full open and close before we leave. Any warranty details are put in writing before work starts. Call (866) 942-6565 to ask about your specific repair.
Clear the area around the gate and its track so the technician can reach the gate and the operator safely. Have the gate’s brand and any manuals or remote controls handy if you have them. Don’t try to force a stuck gate open or closed before the visit, especially a slide gate that’s off its track. Then call (866) 942-6565 to book the visit.
Schedule Your Gate Repair Service in Richmond Today
If your gate won’t open, won’t close, or was never installed right, a gate-only specialist can diagnose it and fix it. Our technicians work on nine brands and handle the full system, from the control board to the hinge. Call (866) 942-6565. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. Estimates are free and the price is agreed before any work starts. You can also read more about our gate repair approach and our electric gate repair service if your system is automated.
Written by the team at Richmond Gate Repair.